Atso Tek
All field notes
STANDARDS 7 min read Atso Tek Trade Desk

SHG Zinc Ingot: What the Grade Name Actually Covers

"SHG" is used in the market for 99.995% zinc, but ASTM B6 reserves Special High Grade for 99.99% and calls 99.995% LME Grade. Why the letters alone are not enough on a purchase order.

Few terms in the zinc trade cause more order disputes than SHG. Buyers ask for "SHG zinc ingot", sellers confirm "SHG", and both believe they agreed on a purity. They often did not. The letters carry one meaning in the standard and a slightly different one in daily market usage, and the gap between them is a real purity step.

What the Standards Say

StandardDesignationMinimum zinc
ASTM B6LME Grade99.995%
ASTM B6Special High Grade99.99%
ASTM B6High Grade99.90%
EN 1179Z199.995%
ISO 752ZN-199.995%

Three standards describe the same top class under three different names. A supplier quoting from the European standard writes Z1; one quoting from ISO writes ZN-1; one quoting from ASTM writes LME Grade. All three mean 99.995%. Meanwhile a trader may write SHG for the same material out of habit. This is why the number is the only unambiguous reference.

Why the Difference Matters

The step from 99.99% to 99.995% looks small on the zinc line, but the trace element limits behind it are not. Lead, cadmium, tin and iron limits tighten, and those four elements are exactly what causes grain-boundary corrosion in zinc die-casting alloys and what affects bath behaviour in galvanizing. A part made from the wrong class can pass incoming inspection and fail months later.

Trace Element Limits

Element99.995% class99.99% class
Lead (Pb)max 0.003%max 0.005%
Cadmium (Cd)max 0.003%max 0.005%
Iron (Fe)max 0.002%max 0.003%
Tin (Sn)max 0.001%max 0.002%
Copper (Cu)max 0.001%max 0.002%

Values are indicative of the classes as written in the common standards; always confirm against the edition your order references, because limits are revised.

How to Write the Order

  • State the number: "Zn min 99.995%".
  • Name the standard and the designation: "ASTM B6 LME Grade" or "EN 1179 Z1".
  • List the trace element maxima you care about, especially lead, cadmium and tin.
  • Require a per-lot Certificate of Analysis with cast and lot numbers.
  • Specify form and unit weight separately — standards do not define them.
  • Require primary metal if remelted secondary zinc is not acceptable.
Is a supplier wrong to call 99.995% zinc SHG?
Not wrong in market terms — the usage is widespread and understood by most traders. It is simply not precise enough for a purchase order, because the same letters also map to the 99.99% class in ASTM B6. Both parties are safer with the number.
Which designation should appear on my specification?
Use the one from the standard your quality system already references, and add the numeric minimum next to it. If you work with European suppliers, EN 1179 Z1 plus "Zn min 99.995%" is unambiguous.
Does the grade name tell me anything about form?
No. Chemistry standards do not define ingot weight, slab size or jumbo blocks. Form, unit weight and bundling are commercial terms and belong in the order confirmation.
What if the CoA shows a grade name but no numbers?
Reject it and ask for a full chemical analysis. A certificate without element lines cannot be verified against your specification and is of no use if a defect appears later.
Atso Tek Zinc CatalogGrade tables, packaging options and shipping documents in one file.PDF ↓
/ Continue reading
QUALITY
Nov 2026

Zinc Ingot 99.995%: Where the Top Purity Is Actually Required

Read article
GUIDE
Oct 2026

Primary vs secondary aluminum ingot: what changes for the buyer

Read article
GUIDE
Oct 2026

What is an aluminum ingot? A7 and A8 explained

Read article
Call WhatsAppGet quote